Home · Services · Bathroom vanity installation and planning

Bathroom vanity installation: size, top, sink, plumbing and light

The vanity is the part of the bathroom you touch every morning. Choosing the right size and top, and lining up pipes, mirror and light around it, is what makes it feel easy to use instead of merely new.

Call (954) 331-7392
Bright kitchen with island and pendant lights
Design inspiration

Start with the room, not the catalog

Vanities are sold in standard widths and styles, and it is easy to fall for one in a showroom that will not suit your bathroom. Start instead with measurements: the wall length available, the door swing, the position of the toilet and shower, and the window or light fixtures nearby. Mark the footprint on the floor with tape and stand there to see how it feels.

Think about who uses the bathroom and when. A shared bathroom used by two people at once may call for a wider vanity with two sinks or a long trough sink. A guest bath may need only a small pedestal or wall hung unit. A bathroom shared by children needs storage they can reach and surfaces that can be wiped clean in seconds.

Our renovation measurements checklist shows what to write down before you shop. If the room is tight, the small bathroom ideas page offers layouts where depth, door swing and storage are balanced with the available space.

Photograph the current bathroom from the doorway and from the shower, and note what annoys you. Maybe the drawers hit the toilet, the sink is too shallow and splashes the floor, or there is nowhere to put a hair dryer. Those small irritations are the real design brief, and they tell your contractor more than a picture of a vanity you like from a magazine.

Sizing the vanity: width, depth and height

Width is the most obvious dimension, but depth deserves equal attention. A deep vanity gives generous counter and storage but projects into walking space. A shallow, narrow depth model, sometimes called a slim vanity, saves space in tight rooms and can help with a door that swings close to the cabinet. Check how far you can pull a drawer fully open without hitting the toilet or tub.

Height matters for comfort. Traditional vanities were lower, while many newer ones sit at a taller, comfort height closer to kitchen counter height. A taller vanity is easier on the back for adults but can feel awkward for children or for someone seated. Think about everyone who will use the sink and choose a height that suits the household, not only the photograph.

Leave clear space on both sides. A vanity tucked tightly against a wall or tub can leave no room to clean or open drawers. Consider where towels will hang, where a trash can will sit and where a stool or hamper might go. Ask your contractor to mock up the size with cardboard or tape so you can walk through the real room before ordering.

Storage inside the cabinet is worth a second look. Drawers divided for daily items work harder than an open cavity with a shelf, and the plumbing in the middle can take away more space than the catalog suggests. Count what you must store, such as towels, cleaners, hair tools and medicines, then ask how each will fit. Tall side cabinets or wall niches can add room without enlarging the vanity.

  • Measure the wall, door swing and drawer clearance before choosing a width.
  • Check depth against the toilet, tub and walkway, not just the wall.
  • Pick a height that suits every user in the household.
  • Leave room on both sides for cleaning and for towels or a hamper.

Cabinet styles: freestanding, wall hung and built in

A freestanding vanity looks like a piece of furniture and sits on the floor. It is the most common type, and it hides pipes in its cabinet. A wall hung or floating vanity attaches to the wall and leaves the floor visible beneath, which makes a small room feel larger and makes floor cleaning easier. It needs strong blocking inside the wall to carry the weight.

A built in vanity is made as part of the room, often with custom cabinets, a full height tower or a tall linen cabinet at the side. It can use awkward spaces well. Pedestal and console sinks offer an airy look with little storage. Each style has trade offs between storage, look and cost, and the right one is the one that solves your storage problem.

Materials need to withstand a humid room. Plywood boxes and sealed finishes generally cope better with moisture than unsealed particleboard. Hardware that resists corrosion matters near the coast. Our guide to humidity and your renovation explains why finish and edge sealing decide how a bathroom cabinet ages in South Florida.

Ventilation protects the vanity as much as the finish does. A bathroom without a working exhaust fan lets steam settle on the cabinet and the mirror, and swelling follows. If your fan is weak or noisy, or if it empties into an attic, the problem is bigger than the vanity. Our page on poor ventilation in bathrooms explains what to look for.

Tops and sinks: materials and shapes

The top is the surface you see and wipe daily. Engineered quartz and natural stone are common choices, and they can be cut to fit unusual sizes. Cultured marble and solid surface tops can include an integral sink with no seam, which is easy to clean. Porcelain and ceramic tops are durable and bright. Laminate is available too, with a different look and care profile.

The sink style changes both look and function. An undermount sink hangs below the top and leaves a clean edge. A drop in sink sits in a cutout with a visible rim. A vessel sink sits on top like a bowl, and it raises the effective height. An integral sink is molded with the top. Each affects how you wipe the counter and how much space is left for your things.

Faucet holes are drilled in the top, so the faucet must be chosen before the top is made. Single hole, three hole spread and wall mounted faucets all require different layouts. A wall mounted faucet also changes the plumbing inside the wall. See selecting fixtures and finishes for help with sequencing these choices.

Backsplash and side splash are small details with large effects. A short splash against the wall protects paint from water, and a taller one can carry tile or stone up behind the faucet. Rimmed or lipped edges collect water, and flush edges wipe clean more easily. Decide whether the top will include a splash, and how it meets the wall, because that line is where moisture most often sneaks in.

Plumbing: where the pipes are and where they need to be

Behind or under every vanity sit the water supply lines, shutoff valves and a drain line that connects to the home's waste system. When you replace a vanity with one of the same width and layout, these often line up neatly. When you change the width, move the sink, or switch from one sink to two, the plumbing may need to move. That is more involved and should be priced as its own item.

The drain location matters. Some drains come through the wall, others through the floor. A new cabinet must have cutouts that fit them, and a wall hung vanity must allow clear access to pipes. A deep drawer under a sink needs a special cutout to clear the trap. Ask your supplier how drawers work with your plumbing, so you do not lose storage to a surprise.

Plumbing in older homes can hold surprises, including corroded valves, outdated supply lines or past repairs. When we open a wall or lift a vanity and find something unexpected, work pauses and it comes to you as a written change order with a price before it proceeds. Specialist plumbing work is done by a specialist trade under our coordination, and permits are pulled where the work requires them.

Also look at the shutoff valves under the old vanity. If they are stiff, leaking or corroded, they are worth replacing while the area is open, since a valve that cannot close properly turns a small repair into a bigger one later. Flexible supply lines age as well. These are small items that belong in the written scope as their own lines, not as surprises on installation day.

Mirrors, medicine cabinets and the wall behind

The mirror and the vanity are a pair. A mirror wider than the vanity can look top heavy, and one much narrower can look lost. Many people hang a mirror that matches the vanity width or is slightly narrower. Mirrors can be framed, frameless, beveled or lit from within, and each has different installation needs such as hidden wiring or extra backing in the wall.

A recessed medicine cabinet needs space between studs and, if it has lights or outlets, electrical work. A surface mounted cabinet is simpler. Two mirrors over a double vanity give each user a space of their own, while a single long mirror creates a continuous look. Think about where the faucet and the mirror edge sit relative to each other so water spray does not cover the glass.

Walls behind a vanity may need repair after the old unit is removed. Paint and drywall often show damage, and tile may stop short or need replacement. Plan these repairs into the scope. Our guide to bathroom tile and waterproofing explains how walls near water are protected, and the same care applies behind and around a vanity.

If the vanity is part of a bigger bathroom update, think about the order of work. Floors, wall tile and paint usually come before the vanity is set, so the cabinet sits on finished surfaces. Setting a vanity first and tiling around it can make later changes difficult. Ask your contractor to show you the sequence in writing, so you know where the vanity falls among the other steps.

Lighting around the mirror

Bathroom lighting shapes how you see your face, and the wrong light can be unkind. Light from above only casts shadows under the eyes and chin. Light from both sides of the mirror at face height is more even and flattering. A fixture over the mirror adds more light, and ambient ceiling lights fill the room. The mix matters more than any single fixture.

Fixtures near water must be suited to the conditions, and your city and your electrician determine what is required. We do not state those rules as fact here. Ask what applies to your layout, and make sure fixtures are chosen before the walls are closed. Wiring for sconces, vanity bars or a lit mirror needs boxes in the right spots at the right height.

If the bathroom has recessed lights, their position should work with the new vanity and mirror, not against them. See the recessed lighting installation page and the interior lighting layers guide for how layers of light work together in a room.

Ordering and lead times

Vanities, tops and faucets are ordered pieces, and each has its own timeline. A stock vanity may be available soon, while a custom one may take longer. Stone and quartz tops are fabricated after measurement, and glass or mirrors may be cut to order. Because these pieces depend on each other, a late delivery of one affects the schedule of all.

We do not promise numbers for lead times. We ask the question early and write down what the supplier tells us. We sequence the work so that rough plumbing and electrical are ready when the cabinet arrives, and the top is templated after the cabinet is set. Our lead times and ordering guide shows how to hold that conversation.

Inspect deliveries when they arrive. Check for chips, scratches and missing hardware before the old vanity is removed, if you can. It is much easier to fix a problem while the old unit is still in place. Keep the packaging until you are sure everything is correct, since returns and replacements depend on it.

Storage of delivered pieces is another practical point. A top or a mirror waiting in a hallway can be chipped by a passing foot or a swinging door. Decide where deliveries will rest, keep them flat or upright as the maker advises, and keep children and pets away. A short conversation about this before the delivery truck arrives prevents damage that no installer can fix.

Installation day and what happens around it

Installation begins with removal of the old vanity: water is shut off, supply and drain lines are disconnected and the unit is taken out. The wall and floor are inspected and repaired if needed. The new cabinet is set, leveled and fastened to wall studs. Shimming and scribing fit it to uneven walls and floors, so edges look intentional.

The top is then installed, followed by the sink if it is separate, and the faucet and drain. Supply lines and drain connections are made and tested for leaks. Caulk seals the top to the wall and the backsplash. Hardware is installed and drawers and doors are adjusted so they close properly. This work is done by trades coordinated under one point of contact.

Every working day ends with cleanup. If you live in the home, plan for periods without the sink and use another bathroom. Our bathroom renovation page shows how a vanity project fits into a larger plan, and the outdated bathrooms page helps you decide how far to go.

Scope, allowances and the finishing details

The written scope for a vanity should name the cabinet, the top, the sink, the faucet, the mirror, the lighting, plumbing adjustments, wall and floor repair, paint and disposal of the old unit. A fixed price is set against that scope before work begins. If you have not chosen yet, an allowance holds a place, and the final price adjusts based on your actual selection.

Be clear about who supplies what. Some homeowners choose and buy their own vanity, and the contractor installs it. Others want everything handled. Either way, the scope should say who orders, who inspects deliveries and who is responsible if something arrives damaged. Our bathroom selections checklist keeps these decisions in one place.

At the end, we walk the punch list together before final payment. You open every drawer and door, run the faucet, test the drain and look at the caulk lines, the mirror and the lights. Anything that needs a correction is written down and fixed.

If you are thinking about a shower change in the same room, plan the two together. A new shower can change where the vanity wall meets the tile, and a vanity can change how the shower door swings. Our walk in shower remodeling page explains how the shower side of the room is planned, and the two projects often share plumbing, tile and a single schedule.

Common questions

Can I replace my vanity with a different size?

Yes, but a different width or sink position can mean moving plumbing, patching walls and repairing the floor. A same size swap is usually simpler. We look at the pipes and walls at the walkthrough and write any adjustments into the scope with a price before work begins.

Do I choose the faucet before the top is made?

Yes. The faucet type decides the holes drilled in the top, and a wall mounted faucet changes the plumbing in the wall. Choose the faucet and sink early, and confirm models against the written scope before the top is cut.

What is the difference between wall hung and freestanding vanities?

A freestanding vanity sits on the floor and hides pipes in its cabinet. A wall hung vanity attaches to the wall, leaves the floor visible and needs strong blocking inside the wall. Both can work well, and the choice depends on storage, style and the room.

What if something is found behind the old vanity?

Work pauses, and the finding comes to you as a written change order with a price before it proceeds. Common findings are old leaks, damaged drywall or worn valves. You decide with the facts in front of you, and nothing is added without your agreement.

How does the mirror relate to the vanity?

They should look like a pair. A mirror close to the vanity width usually looks balanced, and lighting at face height on each side is more even than a single fixture above. Decide mirror and lighting before the walls are closed so wiring and backing are ready.

Will a new vanity affect my schedule?

It can, because cabinets, tops and faucets are ordered separately and the top is templated after the cabinet is set. We ask suppliers about lead times early and sequence the work around them. We do not promise numbers, and we tell you when anything changes.

Want this priced properly? Start with a walkthrough.

Call (954) 331-7392
Tap to Call , (954) 331-7392