Home · Services · Tub to Shower Conversions: Planning Guide

Tub to Shower Conversions: What Changes Behind the Wall

Swapping a tub for a shower looks simple from the doorway, yet it touches the floor, the drain, the walls and the plumbing. Here is how a conversion is planned, step by step, so you know what to ask.

Call (954) 331-7392
Bathroom with marble-look tile, warm wood vanity and gold fixtures
Design inspiration

Why homeowners make the switch

A tub that nobody uses takes up a lot of floor. In many South Florida homes the hall bath still has a standard tub and shower combination, installed when the house was built, while the people living there now prefer a shower. Others find stepping over a high tub wall harder than it used to be, or want a bathroom that feels larger and easier to clean.

The reasons matter because they shape the design. If the goal is a bigger feeling room, glass and a simple floor plane may be the priority. If the goal is easier access, the threshold, seat and grab bar blocking move to the top of the list. If the goal is resale or rental appeal, you may want to keep one tub in the house before removing the last one. That last point is worth discussing with someone who knows your market.

None of these goals is wrong, but each leads to a different plan. Before drawing anything, write down who uses the bathroom, how they use it and what bothers them today. A short list like that makes the walkthrough much more productive.

For a broader look at the room as a whole, see our bathroom renovation overview, and for a design that has no tub at all, our walk in shower remodeling page covers curbs, glass and drains in more depth.

The first walkthrough: what gets measured and checked

Every project starts with a walkthrough and a written scope. For a conversion, the person visiting will look at the tub alcove, the wall behind the fixtures, the floor around the tub, the location of the drain and the access to plumbing from the other side of the wall or below the floor. They will also check what is on the other side of each wall, because a shower may need space that a tub did not.

Dimensions matter. A tub alcove is often about the same footprint as a standard shower base, so a straight swap is possible in many homes. But a shower with a different size, a bench or a wider opening changes the framing. Measurements should be taken at the floor and at a higher point, since walls are not always square.

The scope that comes out of the visit should say what is being removed, what new base and wall system is planned, which fixtures are included and which are not. If you want a niche, a bench or a glass panel, those should be listed by name. Anything that is not listed is not included, so read it carefully.

Our guide to reading a written scope explains how to spot gaps before you sign off on a plan.

Framing and the floor under the tub

A tub sits on the floor and often rests against the studs on three sides. The framing around it may have been built for the tub rather than for a shower. Once the tub is out, the contractor can see whether the floor under it is sound, whether the studs are straight, and whether the rim of the old tub was hiding patched or damaged areas.

Floors under tubs can be a source of surprises. A slow drip around the drain or overflow, or years of splashing that got behind the tub edge, may have softened the subfloor. If any area is soft or stained, the work pauses and you receive a written change order with a price before it goes on. Our page on subfloor repair and leveling explains how those areas are found and corrected.

If you want a curbless or low threshold shower, the floor itself may need to be recessed so water drains inward. That is a structural planning question, not a weekend job. Joists, slab thickness and the age of the home all affect what is possible, and a professional has to look at it in person.

Blocking for grab bars, a bench or a shower niche is added while the walls are open. It costs little to plan it now and a lot to add it later.

Moving or reusing the drain

The drain is the most important decision in a conversion. A tub drain sits near one end, set to suit the tub, and it connects to a trap and pipe beneath. A shower drain may belong in the center, at one side or along a wall as a linear drain, depending on the base and the slope. If the new drain is in the same location as the old one, the work is simpler. If it needs to move, the plumbing below the floor has to be reworked.

Reaching the drain depends on the building. A house on a slab means cutting into concrete, while a home with a crawlspace or an upper floor with access from below may be easier. In a condo or townhome, the plumbing below may belong to a neighbor or to the association. Ask your association about its rules for any work that involves shared lines.

The drain also affects the pan. The base has to slope toward it, and the waterproofing must connect to the drain body in the way the maker specifies. Different shower bases work with different drain types, so the choice of base and drain should be made together.

Plumbing work is done by trades coordinated under the same scope, and permits are pulled where the work requires them. Requirements vary by city, so ask your city building department what applies to a drain change.

  • Keep the drain in place when the new base allows it, to limit plumbing work.
  • Move the drain only when the design truly needs it, and have the new location marked on the scope.
  • Ask whether access from below, above or through the slab is expected.
  • Confirm in writing who handles any permit and inspection tied to the plumbing.

Choosing a shower base

The base is the floor of the shower, and there are several common types. A pre formed base arrives ready to set and has the slope built in. A tile ready foam base is a lightweight pan that accepts tile and a membrane. A custom built mortar bed is shaped on site with slope and a liner or membrane. Each has a different cost in labor, thickness and flexibility, though this page will not quote numbers.

A pre formed base is often the simplest option when the footprint matches a standard size. It can be a good choice for a tub alcove where the opening is regular. Tile ready foam bases offer more freedom in size and drain location, while custom beds can make unusual shapes work, at the price of more steps and more skill.

Thickness is a quiet detail with a big effect. A base that sits high may create a step into the shower that you did not expect, and the curb may be taller than you want. Ask for the finished height of the threshold on the scope, and picture yourself stepping over it every day.

Whichever type is used, the base should be supported evenly with no hollow spots, since a flexing base cracks grout and can break the seal.

It also helps to think about cleaning. A base with a textured surface grips wet feet but holds soap film, while a smoother one wipes clean but needs a mat or a careful choice of tile finish. Pick the surface you will be happy to maintain, since that choice is made once and lived with every day.

Wall systems and what covers them

With the tub gone, the walls around it need a surface that can handle water. Tile over a membrane and backer is the traditional route, and our page on bathroom tile and waterproofing explains the hidden layers in detail. Large panels of solid surface or engineered stone are another route, with fewer seams and less grout to clean.

Panels are appealing for easy cleaning, but they have to be planned carefully. Seams, corners and the joint with the base need sealing in the way the maker specifies, and the walls behind them must still be flat and sound. Panels also come in set sizes, which affects layout and the placement of niches and valves.

Tile offers more variety in color, size and pattern. A tub surround often has tile on three walls and nothing above, while a full shower usually runs tile up higher, often to the ceiling, which brings a different feel. Taller tile means more material and a longer layout, but it protects walls from steam.

Whatever system you choose, ask which membrane or barrier is used, how corners are treated and whether the system has a flood test or inspection step before it is covered. The invisible parts decide how it lasts.

Valves, fixtures and the plumbing wall

A tub and shower combination uses a single wall with a valve at mid height and a spout down low. A shower only setup moves things up: the valve is often placed where you can reach it without standing in the spray, and the shower head sits higher. This means the plumbing in the wall changes, even if the wall itself does not move.

If you want a handheld wand, a rain head or a second control, the valve type matters. Some valves control temperature and flow in one handle, while others separate them. Choosing the valve before the walls close is vital, because the rough in depth has to match the trim you want.

Placement of the niche is another piece to settle. A niche cut into the wall has to be framed and waterproofed with the same care as the rest of the shower, and it should sit where it will not conflict with the pipes. Our bathroom waterproofing explained guide describes why corners like these need extra attention.

Salt air near the coast can affect fixture finishes over time, so ask about finishes suited to your area when you choose trim.

Glass, curtains and the shape of the opening

Once the tub is gone, you have a new decision: how to contain water. Options include a fixed glass panel, a hinged door, a sliding door or a simple curtain rod. A single fixed panel with an open walk in gap gives a clean look, but whether it contains spray depends on the size of the shower and the position of the head.

Glass is ordered after the shower is built, because the exact opening must be measured when walls and tile are finished. That is a lead time to ask about, and our lead times and ordering guide explains how to plan around it without relying on guesses.

A curtain is not a failure. It can be a sensible choice for a hall bath that needs to stay simple, and it leaves the door open for upgrading later. Whatever you choose, plan the hardware location while the walls are open, so there is something solid to anchor to.

Think too about the ventilation. A shower with a large glass enclosure holds steam, and the exhaust fan has to cope. Our page on poor ventilation in bathrooms describes signs that a fan is not keeping up.

If privacy is a concern, for example when the shower sits near a window or a doorway, frosted or textured glass can be discussed during planning. Mention it at the walkthrough so the window, the door swing and the glass layout are considered together instead of one at a time.

Finishing details that make it feel complete

The final details are what turn a conversion into a finished room. The tile edge where wall tile stops, the trim around the opening, the transition between the shower floor and the bathroom floor, and the caulk lines at the corners all draw the eye. They should be planned along with the tile layout rather than left to the last day.

Where the shower meets the bathroom floor, the tile heights may differ. A smooth, clear transition keeps feet safe and water where it belongs. If the bathroom floor is being replaced too, the layout of both can be coordinated so the lines match.

Paint, lighting and the vanity also change the feel. A shower where the tub used to be opens up sight lines, and old fixtures that were hidden by the tub wall now show. Think about whether the vanity, mirror and lighting still suit the room once the space looks different. Our bathroom vanity installation page covers that part of the room.

The punch list is walked together before final payment, so you can point out small items, from a missed corner of caulk to a cabinet door that rubs.

How a conversion project is run

With our team, every conversion begins with a walkthrough and a written scope, and a fixed price is set against that scope before work begins. Permits are pulled where the work requires them and inspections are scheduled. You have one point of contact from estimate to punch list, and the site is cleaned at the end of each working day.

The typical order is protection of the surrounding floors, demolition, framing and plumbing changes, inspection where required, backer and waterproofing, tile, fixtures, glass and final cleaning. Specialist work, such as some electrical work for a fan or a light, is done by a specialist trade under our coordination.

If anything is found behind a wall that was not visible, the work pauses and you receive a written change order with a price before it proceeds. Our explanation of change orders shows what a good one contains.

If you live in an area like Plantation or Hollywood, the process is the same, and this page is general guidance for homeowners in those areas rather than a claim about past work there.

Common questions

Can any tub be replaced with a shower?

Many can, but it depends on the room. A contractor needs to look at the alcove, the drain, the floor and the walls on all sides. If the tub is the only one in the home, you may want to think about how that affects daily life or future buyers before you remove it. Ask for a written scope that covers the details.

Does the drain always have to move?

No. If the new base fits the existing drain location, the drain can stay where it is, which keeps plumbing work limited. If the design needs a center or linear drain, the plumbing below the floor must change. A walkthrough and a written scope should show which case applies to your bathroom.

Do I need a permit for a tub to shower conversion?

Requirements vary by city and building, and they often depend on whether plumbing or structure is being changed. Ask your city building department what applies, and ask your association if you live in a condo or townhome. When permits are required, they are pulled before work begins and inspections are scheduled.

What if the contractor finds rot or damage under the tub?

Work pauses, and the finding comes to you as a written change order with a price before anything proceeds. That way you decide with the facts in front of you. It is common for older bathrooms to hide softened wood near drains and overflows, so it is wise to discuss this possibility at the start.

Can a conversion be made easier to use for someone with limited mobility?

Yes, planning can include a low threshold, a bench, grab bar blocking and a handheld wand. Some of these need floor or framing changes, so they should be decided early and written into the scope. Our aging in place page and accessible features guide go into more detail about options to consider.

Is a glass enclosure required?

No. A glass door or panel, a curtain or an open layout can all work depending on the size of the shower and where the head points. Glass is usually measured after the walls are finished, so ask about ordering time and whether it is part of your scope or handled separately.

Want this priced properly? Start with a walkthrough.

Call (954) 331-7392
Tap to Call , (954) 331-7392